Sandėlyje Karštas produktas
UHLAC1P
UHLAC1P HLAC1P HL-AC1P PANASONIC HL-T1 sensor controller PNP, 12-24VDC
$0.00
JAV dolerių
4344 sandėlyje
Pagrindinės specifikacijos
Prekė:
Specifications
Tipas:
PNP output
Svoris:
Net weight: 140 g approx.
Išsami informacija:
Controller (PNP output)
Tiekėjo informacija
PANASONIC
Produktai: 4316
Paprastai išsiunčiama per 2–3 darbo dienas
Kokybės garantija
Greitas pristatymas
Techninė pagalba
Techninės specifikacijos
| Parametras | Vertė |
|---|---|
| Prekė | Specifications |
| Tipas | PNP output |
| Svoris | Net weight: 140 g approx. |
| Išsami informacija | Controller (PNP output) |
| Produktas | Ultra-compact Laser Collimated Beam Sensor |
| Medžiaga | Enclosure: Polybutylene terephthalateTransparent cover: Polycarbonate |
| Įvesties/išvesties kabelis | 0.09 mm210-core composite cable, 2 m6.562 ftlong |
| Dalies numeris | HL-AC1P |
| Atstatyti įvestį | +V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Produkto pavadinimas | Ultra-compact Laser Collimated Beam Sensor HL-T1 |
| Laiko įvestis | +V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Linijinis išėjimas | Current / voltage output switchable (Note)-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller. |
| Pagrindinės funkcijos | ・Measured value display・Setting value, light amount value resolution display・Standard received light setting・Automatic scaling・Scaling・Display reverse・ECO display・Display digits limitation・Sample hold・Peak hold・Bottom hold・Peak to peak hold・Self peak hold・Self bottom hold・Zero reset・Initial reset・ON-delay timer・OFF-delay timer・One-shot timer・Differentiation・Sensitivity selection・Threshold value direct setting・Positioning teaching・2-point teaching・Automatic teaching・Hysteresis width variability・Monitor focus・Non-measuring time setting・(A – B) calculation(Note：The calculation unit is necessary.)・(A + B) calculation(Note：The calculation unit is necessary.)・Mutual interference prevention (Note：The calculation unit is necessary.)・Laser deterioration detection・Key lock・Zero reset memory |
| Produkto numeris | HL-AC1P |
| Maitinimo įtampa | 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less |
| Lazerio išjungimo įvestis | +V connection: Laser emission haltOpen: Laser emission-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Matavimo ciklas | 150 micro s |
| Taršos laipsnis | 3 (industrial environment) |
| Nulio nustatymo iš naujo įvestis | +V connection: Zero reset operatesOpen: Zero reset ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Srovės suvartojimas | 190 mA or less (when connected to the sensor head) |
| Įvesties/išvesties kabelio prailginimas | Extension up to total 10 m32.808 ftis possible, with 0.09 mm2or more, cable.(Note) If the extension cable is longer than 10 m32.808 ft, then it will not qualify for CE marking. |
| Subskaitmeninis ekranas | 5 digit yellow LED display[RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.] |
| Pagrindinis skaitmeninis ekranas | 5 digit red LED display[RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.] |
| Izoliacijos varža | 20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure |
| Taikoma jutiklio galvutė | HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F |
| Įtampos atsparumas | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| Indikatoriai: Įjungti (ENABLE) | Green LED (lights up during normal operation) |
| Rodikliai: Sprendimų rezultatai | HIGH: Orange LED (lights up when measured value > HIGH threshold value)PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value)LOW: Yellow LED (lights up when LOW threshold value > measured value) |
| Indikatoriai: Nulio nustatymas iš naujo (ZERO) | Green LED (lights up when the zero reset function is enabled) |
| Nustatomas vidutinis mėginių ėmimo dažnis | 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1). |
| Atitiktis CE ženklinimo direktyvai | EMC Directive, RoHS Directive |
| Vertinimo rezultatai (AUKŠTA, TENKINAMA, ŽEMA) | PNP open-collector transistor-Maximum source current: 50 mA-Applied voltage: 30 V DC or less (between judgment output and +V)-Residual voltage: 2 V or less (at 50 mA source current) |
| Indikatoriai: lazerinis spinduliavimas (LD įjungtas) | Green LED (lights up during laser emission) |
| Atsparumas aplinkos poveikiui: aplinkos drėgmė | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Atsparumas aplinkos poveikiui: atsparumas smūgiams | 300 m/s2acceleration (30 G approx.) in X, Y and Z directions three times each |
| Linijinis išėjimas: temperatūros charakteristikos | plus or minus 0.2 % F.S./℃(Note) These are the temperature characteristics of the linear output when the sensor head is connected. |
| Atsparumas aplinkos poveikiui: aplinkos temperatūra | 0 to +50 ℃+32 to +122 ℉(No dew condensation allowed), Storage: -25 to +65 ℃-13 to +149 ℉ |
| Atsparumas aplinkos poveikiui: atsparumas vibracijai | 10 to 150 Hz frequency, 0.7 mm0.028 indouble amplitude in X, Y and Z directions for 80 min. |
| Vertinimo išvestys (AUKŠTA, NEPRITAIKYTA, ŽEMA): Išvesties veikimas | HIGH: ON when measured value > HIGH threshold valuePASS: ON when HIGH threshold value >= measured value >= LOW threshold valueLOW: ON when LOW threshold value > measured value |
| Vertinimo išvestys (AUKŠTA, NEPRITARIA, ŽEMA): išvesčių skaičius | HIGH / PASS / LOW 3 values output |
| Vertinimo rezultatai (AUKŠTA, TENKINAMA, ŽEMA): Panaudojimo kategorija | DC-12 or DC-13 |
| Vertinimo išėjimai (AUKŠTAS, PERLEISTAS, ŽEMAS): Apsauga nuo trumpojo jungimo | Incorporated |
Produkto aprašymas
HLT1 series controller, 12-24 VDC power, PNP digital output, selectable analog output between 4-20mA and ±4V
Pagrindinės savybės
- Pramoninės klasės kokybė
- Atitinka RoHS reikalavimus
- CE sertifikuotas
- 1 metų garantija
Produkto dokumentai
Duomenų lapas
Techninės specifikacijos ir našumo duomenys
Vartotojo vadovas
Montavimo ir naudojimo vadovas
