Sandėlyje Karštas produktas
UST4C11
UST4C11 ST4-C11 PANASONIC Controller for ST4
$0.00
JAV dolerių
3452 sandėlyje
Pagrindinės specifikacijos
Prekė:
Specifications
PFHD:
Refer to the following table(Note： (Probability of dangerous failure per hour) depends on number of single beam sensorST4-A□connected to controller.)
MTTFD:
More than 100 years (Note：Mean time to dangerous failure (in years))
Svoris:
Net weight: 180 g approxGross weight: 390 g approx
Tiekėjo informacija
PANASONIC
Produktai: 4316
Paprastai išsiunčiama per 2–3 darbo dienas
Kokybės garantija
Greitas pristatymas
Techninė pagalba
Techninės specifikacijos
| Parametras | Vertė |
|---|---|
| Prekė | Specifications |
| PFHD | Refer to the following table(Note： (Probability of dangerous failure per hour) depends on number of single beam sensorST4-A□connected to controller.) |
| MTTFD | More than 100 years (Note：Mean time to dangerous failure (in years)) |
| Svoris | Net weight: 180 g approxGross weight: 390 g approx |
| Išsami informacija | Controller |
| Produktas | Compact Type 4 Safety Beam Sensor |
| Medžiaga | Enclosure: ABS |
| Dalies numeris | ST4-C11 |
| Produkto pavadinimas | Compact Type 4 Safety Beam Sensor ST4 |
| Laidų kabelis | Terminal block connector: 0.2 to 1.5 mm2 |
| Maitinimo įtampa | 24 V DC +10-15 % Ripple P-P 10 % or less |
| Reakcijos laikas | OFF response: 25 ms or lessON response: 90 ms or less (auto reset) / 140 ms or less (manual reset) |
| Produkto numeris | ST4-C11 |
| Pagalbiniai išėjimai | PNP open-collector transistor / NPN open-collector transistor (Set using output polarity selection switch)ST4-C11: one outputST4-C12EX: four outputs[PNP output]Maximum source current: 100 mAApplied voltage: same as the supply voltage (between auxiliary output and +V)Residual voltage: 2.5 V or less (at 100 mA source current)[NPN output]Maximum sink current: 100 mAApplied voltage: same as the supply voltage (between auxiliary output and 0 V)Residual voltage: 2.0 V or less (at 100 mA sink current)(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| Nutildymo lempos išvestis | -(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| Prijungimo terminalas | Detachable spring-cage terminal |
| Srovės suvartojimas | 100 mA or less (excluding sensor head ST4-Ax) |
| Taikomi standartai | IEC 61496-1/2 (JIS B 9704-1/2 / UL 61496-1/2) (Type 4), ISO 13849-1:2015 (Category 4, PLe), JIS B 9705-1 (Category 4), IEC 61508-1 to 3 (SIL3), IEC 62061 (SIL3), JIS C 0508-1 to 3 (SIL3), UL 1998, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI/RIA R15.06, ANSI/ISA S84.01 (SIL3)(Note) Complies with those standards only when the controller is used in combination with the sensor head ST4-x. |
| Taikoma jutiklio galvutė | ST4-Ax |
| Atitiktis CE ženklinimo direktyvai | Machinery Directive, EMC Directive, RoHS Directive |
| Pagalbiniai išėjimai: veikimo režimas | OFF when all beams of the connected ST4-Axs are receivedON when one or more beams of the connected ST4-Axs are interrupted |
| Valdymo išėjimai (OSSD 1, OSSD 2) | PNP open-collector transistor / NPN open-collector transistor Dual output x 1 system (Set using output polarity selection switch)[PNP output]Maximum source current: 200 mAApplied voltage: same as the supply voltage (between control output and +V)Residual voltage: 2.5 V or less (at 200 mA source current)Leakage current: 200 micro A or less (including power OFF condition)Maximum load capacity: 1 micro F (from no-load to max. source current)Load wiring resistance: 3 Ohm or less (between control output and load)[NPN output]Maximum sink current: 200 mAApplied voltage: same as the supply voltage (between control output and 0 V)Residual voltage: 2.0 V or less (at 200 mA sink current)Leakage current: 200 micro A or less (including power OFF condition)Maximum load capacity: 1 micro F (from no-load to max. sink current)Load wiring resistance: 3 Ohm or less (between control output and load)(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| Pagalbiniai išėjimai: apsaugos grandinė | Incorporated |
| Išjungimo lempos išvestis: apsaugos grandinė | Incorporated |
| Atsparumas aplinkai: aplinkos drėgmė | 30 to 85 % RH, Storage: 30 to 95 % RH |
| Atsparumas aplinkai: atsparumas smūgiams | 300 m/s2acceleration in X, Y and Z directions three times each |
| Atsparumas aplinkai: aplinkos temperatūra | －10 to +55 ℃+14 to +131℉(No dew condensation or icing allowed),Storage: －25 to +70 ℃－13 to +158℉ |
| Atsparumas aplinkos poveikiui: apsaugos laipsnis | Enclosure: IP40 (IEC)Terminal: IP20 (IEC) |
| Atsparumas aplinkai: atsparumas vibracijai | 10 to 55 Hz frequency, 0.75 mm0.030 indouble amplitude or maximum acceleration 90 m/s2 in X, Y and Z directions for two hours each< |
| Atsparumas aplinkai: izoliacijos varža | 20 MOhm or more with 500 V DC mega between all supply terminals connected together and enclosure |
| Valdymo išėjimai (OSSD 1, OSSD 2): Veikimo režimas | ON when all beams of the connected ST4-Axs are receivedOFF when one or more beams of the connected ST4-Axs are interruptedOFF during lockout |
| Taikoma jutiklio galvutė: nuosekliųjų jungčių skaičius | Interference prevention possible when up to a maximum of 6 sets are connected(When the maximum of 3 controllers are connected together, interference prevention is possible for up to 18 sets) |
| Valdymo išėjimai (OSSD1, OSSD2): Apsaugos grandinė | Incorporated |
| Atsparumas aplinkai: įtampos atsparumas | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
Produkto aprašymas
Standard Control Unit Safety Barrier Category 4 Ple SIL 3, ST4 Series
Pagrindinės savybės
- Pramoninės klasės kokybė
- Atitinka RoHS reikalavimus
- CE sertifikuotas
- 1 metų garantija
Produkto dokumentai
Duomenų lapas
Techninės specifikacijos ir našumo duomenys
Vartotojo vadovas
Montavimo ir naudojimo vadovas
